£0.00View All
(0) Shopping Cart
EuroPound SterlingUS Dollar
Currency
editable-element

Next event: Stand 61 at the London Model Engineering Exhibition at Alexandra Palace 20,21 and 22nd of January 2017

Note from early February 2015 our mail order service is unavailable until further notice ,this website is here as a catalogue , we will be attending ALL our usual shows.

ANAEROBIC CURE THREADLOCK AND RETAINER PRODUCTS SELECTION TABLE / CHART


Thread lock selector chart

 
StarLoc Anaerobic are single part threadlock products for locking all threaded parts against vibration loosening and fatigue / wear plus the added advantages of stopping leakage of fluids and gasses past the threads as well as preventing any build up of corrosion between the two threaded parts.
More reliable than traditional methods,
Easier to use,
Lower cost due to reduced parts,
Threadlockers are 100% reliable unlike other methods of locking ( lock washers, split pins, nylon insert nuts etc... ) and because you can cut down on parts you can lower the costs of an item.
 Starloc threadlockers cure after contact with metals and the absence of air, many other brands of threadlockers wont cure on plated metals or stainless steel etc, Starlocs unique formulations will cure fully even on stainless steel or chrome plate.
If working in cold conditions, with dirty parts or when a high speed cure is required a range of spray on cleaner/primers and accelerators are available to speed cure ( see below )
STARLOC
GRADE
EQUV.
LOCTITE
GRADE
COLOR   VISCOSITY
CPS
GAP FILL 
mm
MAX TEMP  SHEAR
STRENGTH
N/mm2
BREAKAWAY TORQUE
Nm
PREVAILING
TORQUE
Nm
CURE TIME
MINUTES
NAME MAIN USES
9-222 222 PURPLE  1000 .5 160C 2-3.5 4-8 2-4 15 SCREW LOC LOW STRENGTH:EASY DISASSEMBLY:SMALL FASTENERS
 9-242  242 BLUE  1000 .1 160C 12 17-22 5-8 3-7 NUT LOC   MED. STRENGTH GENERAL PURPOSE
 9-243  243 BLUE  1200 .1  160C 12 17-22 5-8 10  BOLT LOC  OIL TOLERANT, FOR AS RECEIVED PARTS
 9-260  260 RED   1300 .25  160C 17 28-32 50-58 10  STUD LOC  HIGH STRENGTH, CAN BE DISASSEMBLED UP TO 6mm
 9-262  262 RED  2500 .25  160C 19 30-35 55-65 15  STUD LOC+  EXTRA STRENGTH STUD LOCK 6mm TO 12 mm
 9-270  270 RED   500 .25  160C 21 32-40 60-70 10  STUD LOC++  FOR FASTENINGS UP TO 25mm FOR NO DISASSEMBLY
 9-272  272 RED   600 .25  160C 22 35-55 55-75 10  STUD LOC+++  EXTRA STRENGTH FOR 25mm+ STUDS
 9-277  277 RED   7000 .25  160C 25 35-55 55-75 10  STUD LOC MAX  PERMANENT GRADE STUD LOC FOR V.BIG STUDS
 9-290  290 GREEN   15 .05 160 C 16  17-22 5-8 5-10  PENETRATING
STUD LOC
 MEDIUM STRENGTH, WICKING GRADE FOR POST APPLICATION
 9-292  292 YELLOW   15 .05  160C 19 28-32 50-58 5-10  PENETRATING
THREAD LOC
 HIGH STRENGTH, WICKING GRADE THREAD LOCK FOR POST APPLICATION
9-022   PINK 10-20 .1 160C 2-4     1-3 SCREW LOCK LOW STRENGTH THREADLOC
FOR USE ON PLASTIC / GLASS / METAL / WOOD PARTS
9-024   CLEAR 10-20 .1 160C 15     1-3 NUT LOCK MEDIUM STRENGTH THREADLOC FOR USE ON PLASTIC / WOOD / GLASS / METAL PARTS
9-077   BLACK 10-20 .1 160C 25     1-3 STUD LOCK HIGH STRENGTH THREADLOC
FOR USE ON PLASTIC / METAL / GLASS / WOOD PARTS
 
Retainer / Bearing Shaft grades selector chart
Single part retainer products for bonding, locking and sealing turned parts, shafts, bearings ( non threaded parts ) , suitable for use on new parts, worn parts, against vibration loosening, vibration fatigue and stress cracking plus the added advantages of stopping leakage of fluids and gasses past as well as preventing any build up of corrosion between the parts.
Retainers are 100% reliable, giving 100% surface contact that is unobtainable with other methods of fitting bearings and shafts etc, press fitting generally gives around 20% to 50 % surface contact, bearing fit gives a totally reliable 100% surface contact that wont leak or work loose over time.
More reliable than traditional methods,
Easier to use, no heating parts before assembly
Lower cost due to faster machining,
tolerances can be relaxed to obtain faster assembly and less rejected parts.

Starloc retainers cure after contact with metals and the absence of air, many other brands of retainer wont cure on plated metals or stainless steel etc, Starlocs unique formulations will cure fully even on stainless steel or chrome plate
If working in cold conditions, with dirty parts or when a high speed cure is required a range of spray on cleaner/primers and accelerators are available to speed cure ( see below )
STAR-LOC
GRADE
EQU. LOCTITE
GRADE
COLOR  VISCOSITY
cPS
GAP FILL
mm
CURED
STRENGTH
N/mm2
SHEAR STRENGTH
BREAKAWAY
Nm
SHEAR STRENGTH
PREVAILING
Nm
CURE
TIME
MINUTES
MAX
TEMP
(DEG C)
NAME USE
9-601 601 GREEN   150  ..15  20 30-35  55-70  10-15  160 GP. RETAINER CLOSE FIT PARTS, ROLER BEARINGS, CAMS ETC
9-603 603 GREEN   125  .05  20 30-35 55-70  10-15  160 GP. RETAINER AS 601, NO PRE CLEANING REQUIRED
9-609 609 GREEN   125  .05  20 30-35 55-70  30-60  160 SLOW CURE GP SLOW CURE VERSION OF 603
9-620 620 YELLOW   1500  .15  25 30-40 55-70  10-15  280 HIGH STRENGTH
HIGH TEMP
FAST CURE
UP TO 450 DEG F HIGH TEMP
9-635 635 GREEN   2500  .15  30 30-40 55-75  10  160 MAX STRENGTH FAST CURE FOR BUSHES,KEYS,SPLINES,TUBING WITH CLOSE FIT
9-638 638 GREEN   2500  .15  30 30-40 55-75  40  160 MAX STRENGTH SLOW CURE AS 635, BUT SLOW CURE
9-641 641 YELLOW   1500  .2  11.5 12-15 16-22  15  160 CONTROLLED STRENGTH
RETAINER
BEARINGS, SHAFTS,REDUCES FRETTING
9-6-48 648 YELLOW   1500  .2  25 30-35 55-70  3-5  180 HIGH STRENGTH,
FAST CURE
UPTO 180 DEG C, ELECTRIC MOTORS,PULLEYS,BEARINGS ETC
9-660 660 RED  3000   .3  25 30-40 55-70 60+   160 EXTRA GAP FILL WORN SHAFTS,PULLEYS ETC

ACCELERATOR / PRIMER ( spray on )

TO SPEED CURE OF THREAD LOCKERS AND RETAINERS

SIMPLY APPLY THIS PRODUCT TO ONE SURFACE BEFORE ASSEMBLY TO SPEED CURE ON CLEAN PARTS, USE DEGREASER / PRIMER TO CLEAN AND PRIME DIRTY PARTS

CODE TYPE DESCRIPTION
ANP N /50  Primer / activator for threadlock / retainer / gasket sealer
solvent based
ANP N/150 "" AS ABOVE, LARGER SIZE
 ANP `T`/50 Primer / activator for threadlock / retainer / gasket sealer
solvent free
 ANP T/150 "" AS ABOVE, LARGER SIZE
DEG / 50  DEGREASER / PRIMER FOR CLEANING PARTS PRIOR TO ASSEMBLY
DEG / 150 DEGREASER / PRIMER FOR CLEANING PARTS PRIOR TO ASSEMBLY